Search results for "width [beam]"
showing 10 items of 168 documents
Optical absorption and electron paramagnetic resonance of theEα′center in amorphous silicon dioxide
2008
We report a combined study by optical absorption (OA) and electron paramagnetic resonance (EPR) spectroscopy on the E{sub {alpha}}{sup '} point defect in amorphous silicon dioxide (a-SiO{sub 2}). This defect has been studied in {beta}-ray irradiated and thermally treated oxygen-deficient a-SiO{sub 2} materials. Our results have pointed out that the E{sub {alpha}}{sup '} center is responsible for an OA Gaussian band peaked at {approx}5.8 eV and having a full width at half maximum of {approx}0.6 eV. The estimated oscillator strength of the related electronic transition is {approx}0.14. Furthermore, we have found that this OA band is quite similar to that of the E{sub {gamma}}{sup '} center in…
The controlled growth of GaN microrods on Si(111) substrates by MOCVD
2015
Abstract In this paper, a selective area growth (SAG) approach for growing GaN microrods on patterned SiN x /Si(111) substrates by metal-organic chemical vapor deposition (MOCVD) is studied. The surface morphology, optical and structural properties of vertical GaN microrods terminated by pyramidal shaped facets (six { 10 1 ¯ 1 } planes) were characterized using scanning electron microscopy (SEM), room temperature photoluminescence (PL) and Raman spectroscopy, respectively. Measurements revealed high-quality GaN microcolumns grown with silane support. Characterized structures were grown nearly strain-free (central frequency of Raman peak of 567±1 cm −1 ) with crystal quality comparable to bu…
Optical, structural, and morphological characterisation of epitaxial ZnO films grown by pulsed-laser deposition
2013
We report on ZnO epitaxial growth by pulsed-laser deposition (PLD) on different substrates, such as quartz, sapphire, and GaN template. Approximately 1 mu m-thick films were grown under different substrate temperatures and background oxygen conditions. X-ray diffraction analysis indicated preferential growth along the c-axis direction with a full-width at half maximum(FWHM) of the rocking curve as narrow as 230 arcs in the case of the GaN template. Low-temperature photoluminescence showed A-excitonic emission near 3.36 eV and a FWHM of (DXA)-X-0 emission as small as 2.89 meV at 9 K. Atomic force microscope measurements showed that roughness as low as 18 nm could be obtained. These results p…
Vacuum ultraviolet excitation of the 1.9-eV emission band related to nonbridging oxygen hole centers in silica
2004
Physical review / B 69, 153201 (2004). doi:10.1103/PhysRevB.69.153201
Characterization of a 10Hz double-pulse non-normal incidence pumped transient collisional Ni-like molybdenum soft x-ray laser for applications
2009
Stable and reliable operation of a nickel-like molybdenum transient collisional soft x-ray laser at 18.9 nm demonstrated and studied with a 10Hz Ti:sapphire laser system proves the suitability of the double-pulse non-normal incidence pumping geometry for table-top high repetition soft x-ray lasers and broadens the attractiveness of x-ray lasers as sources of coherent radiation for various applications. X-ray laser emission with pulse energies well above 1 μJ is obtained for several hours at 10Hz repetition-rate without re-alignment under optimized double pumping pulse parameters including energy ratio, time delay, pulse duration and line focus width.
High-repetition rate acoustic-induced Q-switched all-fiber laser
2005
We report a high repetition rate actively Q switched all fiber laser. The acousto optic interaction controls the cou pling between co propagating core and cladding modes and is used to modulate the optical losses of the cavity, which permits to perform active Q-switching. Using 1.4 m of 300 ppm Er-doped fiber and a maximum pump power of 120 mW, we have obtained up to 1 W peak power pulses, with a pulse repetition rate that can be continuously varied from 1 Hz to 120 kHz and a pulse width that changes from 70 ns to 2.2 μs.
Interferometric Z-scan method for thermo-optical effect studies
2021
We demonstrated a new approach to measuring third-order nonlinear optical effects using an experimental setup incorporating both Z-scan and Mach-Zehnder interferometer methods. This method could be especially purposive for thermo-optical effect studies as it can simultaneously probe thermal gradient profile as well as absolute temperature changes induced by an optical beam. The experimental setup was tested using chloroform. Experimental measurements were carried out using 1064 nm Nd:YAG laser with 8 ns pulse width and 40 kHz pulse repetition rate. The measured nonlinear refractive index of chloroform was mainly induced by the thermo-optical effect. As thermo-optical response depends on bea…
Focusing of surface-acoustic-wave fields on (100) GaAs surfaces
2003
Focused surface-acoustic waves (SAWs) provide a way to reach intense acoustic fields for electro- and optoacoustic applications on semiconductors. We have investigated the focusing of SAWs by interdigital transducers (IDTs) deposited on (100)-oriented GaAs substrates. The focusing IDTs have curved fingers designed to account for the acoustic anisotropy of the substrate. Different factors that affect focusing, such as the aperture angle and the configuration of the IDT fingers, were systematically addressed. We show that the focusing performance can be considerably improved by appropriate choice of the IDT metal pads, which, under appropriate conditions, create an acoustic waveguide within t…
Maximum Power Point Tracker for Standalone PV System Using Neural Networks
2019
In this work, designing and implementation of a maximum power point tracker (MPPT) based on an artificial neural network is proposed. The output voltage of the selected photovoltaic array is controlled by a DC to DC boost converter in a way that the PV array generates the available possible maximum power correspond to the available solar irradiance and temperature. The neural network (NN) is capable of forecasting the required terminal voltage of the PV array in order to generate the possible maximum power. The pulse width modulation (PWM) signal, which drives the boost converter, is generated through a raspberry pi according to the forecasted terminal voltage. The terminal voltage of the P…
Optimization of dual-core and microstructure fiber geometries for dispersion compensation and large mode area
2009
We investigate dual concentric core and microstructure fiber geometries for dispersion compensation. Dispersion values as large as -59 000 ps/(nm km) are achieved, over a broad wavelength range with full width at half maximum exceeding 100 nm. The trade-off between large dispersion and mode area is studied. Geometries with an effective mode area of 30 microm2 and dispersion -19 000 ps/(nm km) and 80 microm2 with -1600 ps/(nm km) are proposed.